KINAX WT707旋转角度测量传感器
KINAX WT707旋转角度测量传感器 具有非接触式电容式感应系统的测量传感器,用于获取轴的角位置并转换为与负载无关的直流信号,与角位置成比例。由于其坚固的设计,它主要用于工厂范围的重型角位置传感器,尤其是机械制造和造船。典型应用在发电行业应运有涡轮叶片,风门和闸板,重型阀门位置;船用和船舶应用的有方向舵,稳定器,推进器位置;其他制造业的应运有滚子位置,铝加工,可以直接替代KINAX 7W1。在测量输出端读取轴上的负载:较大......
产品描述
KINAX WT707旋转角度测量传感器具有非接触式电容式感应系统的测量传感器,用于获取轴的角位置并转换为与负载无关的直流信号,与角位置成比例。由于其坚固的设计,它主要用于工厂范围的重型角位置传感器,尤其是机械制造和造船。典型应用在发电行业应运有涡轮叶片,风门和闸板,重型阀门位置;船用和船舶应用的有方向舵,稳定器,推进器位置;其他制造业的应运有滚子位置,铝加工,可以直接替代KINAX 7W1。在测量输出端读取轴上的负载:较大1000 N(径向)较大500 N(轴向),如果受到振动,轴负载应尽可能低,以确保轴承的较好寿命。
专利非接触式电容系统/无磨损
模拟测量方法,几乎??无限分辨率
旋转角度测量范围:0~5到0~270°,不带齿轮箱0~10°到0~1600圈,带齿轮箱
测量输出:0~1至0/4~20 mA 2、3或4线制连接
允许振动(无附加齿轮):0~200赫兹,10g连续,15 g持续2h; 200~500 Hz,连续5g,10g,2h;
贮存温度:–40~+80 °C
允许振动(无附加齿轮):0~200赫兹,10g连续,15 g持续2h; 200~500 Hz,连续5g,10g,2h;
贮存温度:–40~+80 °C
符合Ex ia IIC T6的“本质安全”防爆保护,可在爆炸性环境中使用
电位计调节量程/优化适应所需的测量范围
输出量特性:线性或V型曲线
驱动轴可以无限旋转:即使超出测量范围的上限值,也不会发生损坏。
坚固外壳中的表面安装装置:抗振动和冲击,适用于机械制造和造船业
具备海上实行能力(以前是GL,Germanischer Lloyd)
Despription | Blocking code | No-go with blocking code | Order- Code | ||
KINAX WT707 Order-Code 707 - xxxx xxxx xxxx xx | 707- | ||||
1. |
Version of the transmitter Standard |
A |
1 |
||
ATEX EX II 2G Ex ia IIC T6 Gb | B | 2 | |||
Sea water version | N | 3 | |||
Sea water version with gear | O | 4 | |||
ATEX EX II 2G Ex ia IIC T6 Gb, sea water version | BN | 7 | |||
ATEX EX II 2G Ex ia IIC T6 Gb, sea water version with gear | BO | 8 | |||
IECEx Ex ia IIC T6 Gb | B | A | |||
IECEx Ex ia IIC T6 Gb, sea water version | BN | B | |||
IECEx Ex ia IIC T6 Gb, sea water version with gear | BO | C | |||
2. |
Sense of rotation Calibrated for sense of rotation clockwise |
D |
1 |
||
Calibrated for sense of rotation counter-clockwise | D | 2 | |||
For V-characteristic (not possible for instruments with additional gear). | E | 3 | |||
Calibrated for both senses of rotation (for measuring ranges ≤ 90° only) | M | 4 | |||
Lines 1 and 2: Instruments with ranges 0 … ≥ 5 to 0 … ≤ 150° are usable in both senses of rotation. Instruments with ranges 0 … > 150° to 0 … ≤ 270° can be changed to the other direction (Beginning and end of the measuring range must be readjusted). Sense of rotation for transmitters with additional gear see “Feature 13 and 14”. |
|||||
3. |
Measuring range (measuring input) 0...10° angle |
1 |
|||
0...30° angle | 2 | ||||
0...60° angle | 3 | ||||
0...90° angle | 4 | ||||
0...180° angle | 5 | ||||
0...270° angle | 6 | ||||
Non-standard (0 to ≥ 5° to 0 to < 270°) [angle] | 9 | ||||
V-characteristic [±angle] | A | ||||
Line 9: Non standard 0... ≥ 5 to 0... < 270 Calibrated for both senses of rotation, non standard range 0... ≥ 5 to 0... < 90° Line A: Specify start MA and end ME of measuring range! Observe the limits for (MA [± °] ≥ 10 and ME [± °] ≤ 150) and give both angles separated by an oblique stroke, e.g. [± °] 15 / 90! |
|||||
4. |
Output signal (measuring output) / Connection version 0...1 mA, 3- or (4)-wire connection |
A |
|||
0...5 mA, 3- or (4)-wire connection | B | ||||
0...10 mA, 3- or (4)-wire connection | C | ||||
4...20 mA, 2-wire connection or 0...20 mA, 3- or (4)-wire connection (adjustable with poteniometer) |
H | D | |||
4...20 mA, 3- or (4)-wire connection | E | ||||
0...20 mA, 4-wire connection (only possible with AC/DC-power supply (DC-, AC-power pack)) | L | F | |||
Non standard, 3- or (4)-wire connection 0...>1.00 mA to 0... <20 mA [mA] | Z | ||||
Lines A to Z: Rext max. see Section “Technical data”, 4-wire connection, with electric isolation only possible with DC/AC power supply (AC/DC power pack). 2-, 3- or 4-wire connection, without electric isolation only possible with DC power supply. |
|||||
5. |
Power supply 24...60 VAC/DC, with electric isolation |
F |
BH |
1 | |
85...230 VAC/DC, with electric isolation | F | BH | 2 | ||
12...33 VDC, without electric isolation | K | BL | A | ||
12...30 VDC (Ex), without electric isolation | K | AL | B | ||
Lines 1 and 2: Not possible for DC/AC power supply at output signal “Feature 4, line D”! | |||||
6. |
Mounting mode Without foot/flange |
0 |
|||
With foot (mounted) | 1 | ||||
With flange (mounted) | 2 | ||||
7. |
Material of transmitter rear cover / Routing of connection cable Plastic / connector less cable plug, socket mounted for cable routed to the rear |
P |
1 |
||
Plastic / connector less cable plug, socket mounted for cable routed to the front | P | 2 | |||
Plastic / connector with cable plug, socket mounted for cable routed to the rear | P | 3 | |||
Plastic / connector with cable plug, socket mounted for cable routed to the front | P | 4 | |||
Metal / 2 glands PG11 Recommeded for AC/DC power supply, 4-wire connection with electric isolation |
5 |
||||
8. |
Special features Without (order code complete) |
Y |
0 |
||
With | 1 | ||||
9. |
Settings (span adjustment) Without extended setting range |
0 |
|||
Extended setting range + 5 % /-60 % | Y | A | |||
Restriction: for angle ≥ 60°, supplementary error 0.2 % also possible on versions with additional gear |
气候等级:标准(Non-Ex):温度– 25~+70 °C,相对湿度≤95%,不凝结。
带有改进气候等级(Non-Ex):温度– 40~+70 °C,相对湿度≤95%,不凝结。
防爆保护:温度T6 – 40~+55 °C,温度在T5 –40~+70 °C,温度在T4– 40~+75 °C
外壳保护:IP67符合EN60529标准,IP69k符合EN40050-9标准
抖动:IEC60068-2-6,10g连续,15g(每2小时在3个方向内)/0...200Hz,5g连续,10g(每2小时在3个方向内)/200 … 500 Hz
震动:IEC 60 068-2-27, 3 x 50g(每个轴和方向10个脉冲)
电磁适应性:标准适用于抗扰度EN61000-6-2和观察干扰发射EN61000-6-4
防爆保护:本质安全Ex II 2 G / Ex ia IIC T6 符合EN 60 079-0: 2006和EN 60 079-11: 2007
Camillebauer企业位于景色旖旎的瑞士沃伦(苏黎世附近),成立于1900年(瑞士巴塞尔),1944年起开始自主研发和生产,是一家秉承瑞士品质和创新精神的中型企业,在全球范围内向能源生产、输送及用户端,提供客户化产品和解决方案,为用户创造价值,Camillebauer企业以传承瑞士品质和积极创新的姿态,重新定义基于新能源时代的四大核心技术领域(1)测量和显示(2)电能质量(3)控制和监控(4)App和系统解决方案,藉此从容应对世界对能源日趋复杂要求之挑战。电力,不像墙上的插座那么简单!
Camillebauer企业位于景色旖旎的瑞士沃伦(苏黎世附近),成立于1900年(瑞士巴塞尔),1944年起开始自主研发和生产,是一家秉承瑞士品质和创新精神的中型企业,在全球范围内向能源生产、输送及用户端,提供客户化产品和解决方案,为用户创造价值,Camillebauer企业以传承瑞士品质和积极创新的姿态,重新定义基于新能源时代的四大核心技术领域(1)测量和显示(2)电能质量(3)控制和监控(4)App和系统解决方案,藉此从容应对世界对能源日趋复杂要求之挑战。电力,不像墙上的插座那么简单!
文章来源于Camillebauer